NI-DAQ 8.5 Readme
Copyright 2003–2007 National
Instruments. All rights reserved.
Under the copyright laws, this publication may not be reproduced
or transmitted in any form, electronic or mechanical, including photocopying,
recording, storing in an information retrieval system, or translating, in whole
or in part, without the prior written consent of National Instruments
Corporation.
National Instruments, NI, ni.com,
and LabVIEW are trademarks of National Instruments Corporation. Refer to the
Terms of Use section on ni.com/legal for
more information about National Instruments trademarks.
Patents
For patents covering the National Instruments products,
refer to the appropriate location: Help»Patents in
your software, the patents.txt file on your CD,
or ni.com/patents.
Thank you for using NI-DAQmx, version 8.5f5. This release differs from 8.5f3
with the inclusion of the following changes:
- Updated to MAX 4.2.1 which resolves an issue with MAX 4.2 where Real-Time
targets may not be listed when unconfigured or in Safe Mode. Refer to ni.com/kb and search for KnowledgeBase entry
47IC8SCW.
- Resolves an issue that may have resulted in delays in task creation and
editing. The original issue is only present in NI-DAQmx 8.5f3 and affects tasks
larger than approximately 64 channels in size.
|
The Readme contains the following main sections:
NI-DAQ 7.x and Later Software
This section provides an overview of NI-DAQmx and Traditional
NI-DAQ (Legacy). National Instruments measurement devices are packaged with
NI-DAQ driver software, an extensive library of VIs and ANSI C
functions you can call from your application software, such as LabVIEW or
LabWindows™/CVI™, to program your NI measurement devices.
Measurement devices include DAQ devices such as the M Series multifunction I/O
(MIO) devices, signal conditioning modules, and switch modules. Driver software
has an application programming interface (API ), which is a library of
VIs, functions, classes, attributes, and properties for creating applications
for your device.
NI-DAQ 7.x and later includes two NI-DAQ drivers,
NI-DAQmx and Traditional NI-DAQ (Legacy), each with its own APIs, hardware
configuration, and software configuration.
Choosing the API to Use
This section includes information on choosing the right API for
your device and application.
NI-DAQmx
NI-DAQmx is the latest NI-DAQ driver with new VIs and functions
and development tools for programming measurement devices. You should install
and use NI-DAQmx if you are using devices supported by NI-DAQmx; refer to Device Support. If you are using a TEDS sensor, you can
use only NI-DAQmx.
If you are using NI application software with NI-DAQmx, you must
use LabVIEW, LabWindows/CVI, or Measurement Studio version 7.x and
later, LabVIEW SignalExpress 2.x, or the LabVIEW Real-Time Module 7.1
or later.
To use Visual C# or Visual Basic.NET, you must use NI-DAQmx.
You can also use supported versions of
Visual Studio to create NI-DAQmx applications with Visual Basic 6.0 and ANSI
C.
Traditional NI-DAQ (Legacy)
Traditional NI-DAQ (Legacy) is an older driver with outdated
APIs for developing data acquisition, instrumentation, and control applications
for older National Instruments DAQ devices. Traditional NI-DAQ (Legacy) has the
same VIs and functions and works the same way as NI-DAQ 6.9.3, except you can
use Traditional NI-DAQ (Legacy) and NI-DAQmx on the same computer, and some
hardware and software is no longer supported.
You should use Traditional NI-DAQ (Legacy) only in
certain circumstances.
- You have a device that is not supported by NI-DAQmx, such as the AT E
Series multifunction DAQ devices; refer to Device
Support.
- You are using LabWindows/CVI or Measurement Studio version
6.x.
- You have existing NI-DAQ 6.9.x or Traditional NI-DAQ (Legacy)
applications that you cannot port to NI-DAQmx now. You can continue to use
applications developed in Traditional NI-DAQ (Legacy) that control older devices
in the same system with NI-DAQmx applications for newer devices. Refer to Using NI-DAQmx and Traditional NI-DAQ (Legacy) on the Same
Computer.
- You have an NI modular instrument device that requires Traditional NI-DAQ
(Legacy).
New Features
The following main features were added in this release.
- Newly supported devices in NI-DAQmx—NI 9201, NI 9203, NI 9217, NI
9219, NI 9221, NI 9229, NI 9234, NI 9239, NI 9264, NI 9265, NI 9403, NI 9411, NI
9422, NI 9423, NI 9425, NI 9435, NI 9474, NI 9476, NI 9477, NI 9485, NI
PCIe-6536, NI PCIe-6537, NI PXI-2545, NI PXI-2546, NI PXI-2547, NI PXI-2548, NI
PXI-2549, NI PXI-2554, NI PXI-2555, NI PXI-2556, NI PXI-2557, NI PXI-2558, NI
PXI-2559, and NI USB-6525. Refer to Device Support for
a complete list of devices.
- DAQ Assistant support for LabVIEW SignalExpress—You can now use the
DAQ Assistant with LabVIEW SignalExpress. LabVIEW SignalExpress LE, an
easy-to-use configuration-based tool specifically designed for data logging
applications, is included on every NI-DAQmx CD.
- Windows Vista x64 kernel support
- Windows Vista 32-bit support for the SCXI-1600
- cDAQ TEDS support for the NI 9219, NI 9233, NI 9234, and NI 9237
- SCXI calibration—Channel calibration is now supported for the
SCXI-1126, SCXI-1141/1142/1143, SCXI-1530/1531, and SCXI-1540.
NI-DAQmx Known Issues
This section covers issues specific to NI-DAQmx.
Aborting Single-Point Reads and Writes in LabVIEW
Single-point reads and writes do not respond to the
Abort Execution button in LabVIEW.
Counter Behavior of the NI DAQPad-6015/6016 for USB
When performing buffered counter measurements on both ctr0 and
ctr1 simultaneously, ctr1 returns duplicate counts. If you do not use ctr0 or if
ctr0 performs a software-timed measurement, ctr1 functions properly.
DAQ Assistant Maximum Channel Count
The maximum number of channels you can have in a task created
with the DAQ Assistant is 512 channels.
DAQmx Is Read or Write Late Obsoleted
The existing DAQmx Is Read or Write Late function/VI has been
obsoleted and no longer has any effect. Applications that must check whether
they are maintaining real-time behavior have two options. For the strictest
checking, use the Wait for Next Sample Clock function/VI. Refer to your API
reference help, such as the LabVIEW Help or the NI-DAQmx C Function
Reference Help, for more information on this function/VI. To check only
whether the application misses any analog input samples, set the Report
Missed Samples property to True on the analog input task. In LabVIEW,
the Report Missed Samples property is in the Real Time property
node. For more details, National Instruments strongly recommends that you read
the document referred to by the Wait for Next Sample Clock function/VI.
Duplicate Count Prevention Defaults
The default setting for the duplicate count prevention
attribute/property on M Series and TIO-based counters has been changed. This
change affects all input counter operations, with the exception of single-point
edge counting and position measurements. Duplicate count prevention is now on
by default as long as the following conditions are met:
- The duplicate count prevention attribute/property has not been explicitly
set.
- The selected counter timebase source is not set to an internal
timebase.
- The prescaler attribute/property has not been set.
- The counter output event has not been configured.
To learn more, refer to Duplicate Count Prevention in
the NI-DAQmx help.
Existing .NET Project Produces Build Errors
If you are using NI-DAQ with a .NET language, an existing
project can produce build errors that read "error CS0011: Referenced class
'className' has base class or interface
'NationalInstruments.ISynchronizeCallbacks' defined in an assembly that is not
referenced. You must add a reference to assembly 'NationalInstruments.Common'."
To eliminate this error, add a reference to the NationalInstruments.Common
assembly to the project. This problem occurs when an existing project was built
with NI-DAQ 7.2 or earlier and is rebuilt with NI-DAQ 7.3 or later.
LabVIEW Long Property Names
When importing or exporting .ini
files and tab-delimited text, LabVIEW long property names are not supported.
Only English LabVIEW short property names, CVI property names, and C++/.NET
class.property names are supported.
Multichannel SCXI Convert Clock Default Rate Change in NI-DAQmx 8.5
Starting in NI-DAQmx 8.5, a delay of 20 µs was added to
the fastest possible channel conversion rate on an SCXI chassis connected to a
16-bit or 18-bit E or M Series device. If a sample rate is set fast enough to
require a convert clock rate greater than the default rate, warning 200011 is generated, informing the user that the
accuracy of the measurement might be compromised. However, since this is a
warning, the convert clock used is based on the rate needed by the sample
clock set by the user (that is, convert clock = sample clock * number of
channels).
For SCXI chassis containing a module with track-and-hold
circuitry, 10 µs of padding is now added to the fastest possible
conversion rate when connected to a 12-bit E Series device.
These changes ensure the most accurate data is being acquired.
However, if the effect on the performance due to this change
is too great (such as on an RT system using hardware-timed single point in a
control loop), then the convert clock rate attribute can be explicitly set,
overriding the default rate.
This change affects only multichannel acquisitions.
In versions prior to NI-DAQmx 8.5, only 10 µs of delay was
added
to the fastest possible channel conversion rate on an SCXI chassis without a
track-and-hold module connected to any DAQ device. In these versions of
NI-DAQmx, no warning was generated when the sample rate needed a
faster convert clock than was chosen by default. When an SCXI chassis with a
track-and-hold module was present, the convert clock rate selected was the
fastest possible rate that the DAQ device can handle, up to 333kHz.
.NET Remoting
Accessing objects in the DAQmx .NET class library from a remote
application domain with .NET Remoting is not supported in Microsoft Visual
Studio .NET 2003.
NI DAQCard-6715 Analog Output
Hardware-timed single-point mode and hardware-timed nonbuffered
mode are nonfunctional. Your application is using hardware-timed nonbuffered
mode if you have set up a sample clock and a buffer size of 0, or set up a
sample clock, but do not begin writing until after you start the task. All other
waveform and static analog output modes work as expected.
NI-DAQmx .NET Framework 1.1 Help Shortcut
A shortcut to the NI-DAQmx .NET Framework 1.1 Help is
installed by default at Start»All Programs»National
Instruments»NI-DAQ»NI-DAQmx .NET Framework 1.1 Help. This
documentation is in the Microsoft Help 2.0 format and requires a Microsoft Help
2.0 viewer to be displayed. A Microsoft Help 2.0 viewer is installed with both
Microsoft Visual Studio .NET and the Microsoft .NET Framework SDK. The SDK is
freely available from MSDN at http://www.microsoft.com/downloads
. If you do not have either of these products, you will need a standalone
Microsoft Help 2.0 viewer to display the documentation. Some Help 2.0 viewers
are available for download, such as Helpware's H2Viewer.
NI PCI-6704 and PXI-6704 Current Output Accuracy
NI-DAQmx 8.3 changes the algorithm used to scale the 20mA
current outputs of the NI 6704 to a method that matches the behavior of
Traditional NI-DAQ (Legacy). Previous versions of the NI-DAQmx driver use a
second method.
The effect of the change is that when NI-DAQmx programs the 6704
to output current, the actual current level of the 6704 is 10 µA higher
with
NI-DAQmx 8.3 compared to previous versions of NI-DAQmx. The actual current
output with NI-DAQmx 8.3 is the same compared to Traditional NI-DAQ
(Legacy) drivers. This change has no effect on the voltage outputs of the
6704.
Because of this change, NI recommends that you externally
calibrate NI 6704 devices with NI-DAQmx 8.3 (or later) before using devices with
the NI-DAQmx 8.3 (or later) driver. NI 6704 devices that ship with NI-DAQmx 8.3
have already been calibrated with NI-DAQmx 8.3. For other NI 6704 devices, refer
to the manual calibration procedure available at
ni.com/calibration.
NI PCI-7041/6040E Support
The NI PCI-7041/6040E device for LabVIEW RT is no longer
supported in NI-DAQmx 8.3 and will not be supported in future versions. The
device continues to be supported in NI-DAQmx 8.1 and earlier.
Resolving Compiler Warnings from SynchronizingObject in Visual Studio 2005
SynchronizingObject has been
obsoleted in Measurement Studio class libraries for .NET Framework 2.0.
Accessing this property produces compiler warnings. If you were using
SynchronizingObject in .NET Framework 1.1,
you must update your code to use SynchronizationContext in .NET Framework 2.0.
For more information about SynchronizationContext,
refer to Events, Callbacks, and Thread Safety in Measurement Studio Class
Libraries in the NI-DAQmx .NET Framework 2.0 help. The help can be launched
from Start»All Programs»National
Instruments»NI-DAQ».NET
Framework 2.0 Help.
Some Devices Enumerate Twice
Supported CompactRIO devices that fit into the NI USB-9162
carrier enumerate twice in MAX. When a device, such as the NI USB-9421, is first
installed, it appears as the NI USB-9162 before appearing as the correct
device.
Temperature Sensors and the Mass Termination USB-6251/6259
When configuring the SCB/SCC-68, the temperature sensor check
box is greyed out when the block is connected to either connector of a Mass
Termination USB-6251 or USB-6259
USB-9xxx Devices
Unplug your USB-9xxx and plug it back in or power the
USB device down and up after upgrading NI-DAQmx. If the USB-9xxx is
connected to a USB hub, make sure to disconnect the USB-9xxx from the
hub, not the hub from the computer. Disconnecting power from the USB device
causes installed devices to load the correct version of the firmware.
USB Device Removal During a DAQ Operation
If a USB DAQ device is unplugged while a DAQ operation is being
performed, unexpected results may occur, including causing the operating system
to hang. In these occasional, extreme cases, you must reboot the computer. NI
recommends stopping all DAQ operations on a USB device before unplugging the
device from the computer.
Using the C++ API from Multiple DLLs in the Same Process
If you use the C++ API from multiple DLLs in the same process,
you must access the API from only one DLL at a time. You must stop using the API
in one DLL and destroy all API objects before using the API in another DLL.
Virtual TEDS Data for the NI 9233/9237
If you connect hardware TEDS to NI 9233/9237 channels configured
with virtual TEDS, the virtual TEDS will be replaced with hardware TEDS data
after upgrading to NI-DAQmx 8.5.
Using NI-DAQmx and Traditional NI-DAQ (Legacy) on the
Same Computer
Existing applications developed with earlier versions of NI-DAQ
will run under Traditional NI-DAQ (Legacy). You can use both the Traditional
NI-DAQ (Legacy) API and the NI-DAQmx API on the same computer with the following
restrictions:
- Only one API controls a given device at one time.
| – |
After using a device in NI-DAQmx, you must unreserve all NI-DAQmx tasks that
are using that device before you can use that device through Traditional NI-DAQ
(Legacy). If you use a device in NI-DAQmx and then use it in Traditional NI-DAQ
(Legacy) without unreserving the NI-DAQmx tasks, error code -10461 is returned. To unreserve NI-DAQmx tasks, call
the DAQmx Clear Task VI or functions. |
| – |
After using a device in Traditional NI-DAQ (Legacy), you must reset the
device before you can use that device in NI-DAQmx, or error code -200324 is returned.
For SCXI devices, you must reset the communicating DAQ device in
Traditional NI-DAQ (Legacy) before using it in NI-DAQmx. For example, E Series
DAQ devices use lines 0, 1, 2, and 4 on port 0 to communicate with the SCXI
module. Error code -200158 is returned if you do
not reset the communicating device in Traditional NI-DAQ (Legacy) before using
it in NI-DAQmx as follows:
- Call the Traditional NI-DAQ (Legacy) Device Reset VI or the Init_DA_Brds function
- To reset devices in Traditional NI-DAQ (Legacy) from MAX, you must reset all
devices at once. Right-click the Traditional NI-DAQ (Legacy)
Devices folder in MAX and select Reset Driver for Traditional
NI-DAQ (Legacy). For a remote RT target, you must use the Traditional
NI-DAQ (Legacy) Device Reset VI.
|
- In an SCXI data acquisition system, you must use the same API to program all
devices—connected DAQ devices and inserted SCXI modules.
Refer to ni.com/support for
details and instructions about the following topics:
- How to add NI-DAQmx code to a Traditional NI-DAQ (Legacy) application
- How to run both Traditional NI-DAQ (Legacy) applications and NI-DAQmx
applications that use the same device
Support in NI-DAQ 8.5
Operating System Support
| NI-DAQ Version |
Windows Vista 641 |
Windows Vista 321 |
Windows XP |
Windows 2000 |
| NI-DAQmx 8.5 |
Yes |
Yes |
Yes |
Yes |
| Traditional NI-DAQ 7.4.4 |
No |
No |
Yes |
Yes |
| 1Windows Vista Business edition |
For OS-specific device support information, refer to
ni.com/support/daq/versions.htm.
| Caution If you plan
to perform an upgrade of your system from a prior version of Microsoft Windows
to Microsoft Windows Vista, you are required to uninstall all National
Instruments software prior to performing the upgrade. After the upgrade has been
completed, you can reinstall your National Instruments software. |
NI-DAQmx 8.5 supports PharLap only with the LabVIEW Real-Time
Module 7.1 and later.
Measurement Studio requires Visual Studio .NET 2003, which
requires Windows 2000/XP. If you are using the DAQmx .NET Library, the .NET 1.1
framework is required. .NET 1.1 requires Windows 2000/XP.
Windows NT users must use NI-DAQmx 7.5 or Traditional NI-DAQ
(Legacy) 7.4.
Windows Me/98 users must use NI-DAQ 7.1 or earlier. Windows 95
users must use NI-DAQ 6.9.3 or earlier
LabVIEW Real-Time for the Macintosh 7.1 will not be supported in
LabVIEW 8.0 due to low demand. However, National Instruments continues to
support PCI and USB data acquisition hardware using NI-DAQmx Base. Macintosh
systems can continue to serve as hosts to real-time targets. For more
information on supported products, refer to ni.com/mac.
For operating system-specific installation instructions, use the
Hardware Installation/Configuration Troubleshooter at ni.com/support/install.
To find and download an earlier version of NI-DAQ that supports
other operating systems, refer to ni.com/downloads.
NI Application Software Support
The following table lists the NI application software versions
supported by NI-DAQmx and Traditional NI-DAQ (Legacy). If you are not using NI
application software, refer to Microsoft Visual Studio Support.
Starting with NI-DAQ version 7.4.2, Traditional NI-DAQ
(Legacy) installs support only for the latest version of LabVIEW found on the
system. The Traditional NI-DAQ (Legacy) API is mass-compiled in LabVIEW version
7.0. See LabVIEW Support in the Traditional NI-DAQ (Legacy) Readme
for more information.
| NI Application Software |
Versions Supported by NI-DAQmx |
Versions Supported by Traditional NI-DAQ (Legacy) |
| LabVIEW |
7.1 and later |
7.0 and later |
| LabVIEW Real-Time Module |
7.11 and later |
7.0 and later |
| LabWindows/CVI |
7.x and later |
6.0 and later |
| Measurement Studio |
7.x and later |
6.0 and later |
| LabVIEW SignalExpress |
2.x and later |
|
| 1To use LabVIEW Real-Time Module 7.1 with
NI-DAQmx,
you must use NI-DAQmx 7.2 or later. |
| 2Traditional NI-DAQ (Legacy) with the Measurement
Studio ActiveX control. These versions do not include a Measurement Studio C++
or .NET interface. |
.NET and Measurement Studio Visual C++ Example
Paths
Starting with NI-DAQ version 8.5, the .NET and Measurement
Studio 8.1.1 Visual C++ example paths have changed. In the following paths,
x is the letter of the hard drive.
The .NET example paths for Windows Vista are
x:\Users\Public\Documents\National
Instruments\NI-DAQ\Examples\DotNET1.1 and
x:\Users\Public\Documents\National
Instruments\NI-DAQ\Examples\DotNET2.0.
The Measurement Studio 8.1.1 Visual C++ example paths for
Windows Vista are x:\Users\Public\Documents\National
Instruments\NI-DAQ\Examples\MStudioVC2003 and
x:\Users\Public\Documents\National
Instruments\NI-DAQ\Examples\MStudioVC2005.
The .NET example paths for Windows XP and Windows 2000 are
x:\Documents and Settings\All Users\Documents\National
Instruments\NI-DAQ\Examples\DotNET1.1 and x:\Documents and Settings\All
Users\Documents\National Instruments\NI-DAQ\Examples\DotNET2.0.
The Measurement Studio 8.1.1 Visual C++ example paths for
Windows XP and Windows 2000 are x:\Documents and Settings\All
Users\Documents\National Instruments\NI-DAQ\Examples\MStudioVC2003 and
x:\Documents and Settings\All Users\Documents\National
Instruments\NI-DAQ\Examples\MStudioVC2005.
For more information, refer to Where To Find Examples
in the NI Measurement Studio Help.
Microsoft Visual Studio Support
The following table lists the programming languages and
Microsoft Visual Studio versions supported by NI-DAQmx and Traditional NI-DAQ
(Legacy).
| Programming Language |
Visual Studio Versions Supported by NI-DAQmx |
Visual Studio Versions Supported by Traditional NI-DAQ
(Legacy) |
| ANSI C |
6.0 and later |
6.0 and later |
| C++ |
2003 (7.1)1 |
— |
| Visual Basic 6.0 |
6.0 SP62 |
6.0 SP63 |
.NET Framework 1.1
Languages
(C# and
Visual Basic.NET) |
2003 (7.1) |
— |
.NET Framework 2.0
Languages
(C# and
Visual Basic.NET) |
2005 (8.0) |
— |
| 1 Requires Measurement Studio
7.x |
| 2 Support through ANSI C type
library |
| 3 Support through ActiveX |
Earlier versions of NI-DAQ support other application software
and language versions. To find and download an earlier version of a driver,
refer to ni.com/downloads.
LabVIEW SignalExpress
LabVIEW SignalExpress LE gives you a 30-day trial of the Full
version of LabVIEW SignalExpress. For more information on the trial
version, refer to Getting Started with LabVIEW SignalExpress,
installed by default at Start»All Programs»National
Instruments»LabVIEW SignalExpress.
Device Support
The following lists detail the devices supported in NI-DAQmx and
Traditional NI-DAQ (Legacy). Device support is divided into the
following categories:
For OS-specific device support information, refer to
ni.com/support/daq/versions.htm.
For MXI-3 and MXI-4 OS-specific support information, refer to ni.com/kb and search for KnowledgeBase entry
45MA9LF7.
Devices Supported Only in NI-DAQmx
NI-DAQmx supports the following devices:
- NI 9201 C Series 8-channel, ±10 V, 12-bit analog input module
- NI 9201 (DSUB)
- NI 9203 C Series 8-channel, ±20 mA, 16-bit analog input module
- NI 9205 32-channel, 16-bit analog input module with gain and analog
trigger (AI, PFI only)
- NI 9206 32-channel, 16-bit analog input module for fuel cells (AI, PFI
only)
- NI 9211 12 S/s, 24-bit, thermocouple analog input, 4-channel scanned analog
input module
- NI 9215 100 kS/s, 16-bit, 4-channel isolated SMIO analog input module
- NI 9215 (BNC)
- NI 9217 C Series 4-channel, 24-bit, 100 ohm RTD analog input module
- NI 9219 C Series 4-channel, 24-bit, universal analog input module
- NI 9221 C Series 8-channel, ±60 V, 12-bit analog input module
- NI 9221 (DSUB)
- NI 9229 C Series 4-channel, ±60 V, 24-bit, simultaneous analog input
module
- NI 9233 50 kS/s, 24-bit, 4-channel dynamic signal acquisition module
- NI 9234 4-channel, 51.2 kS/s, 24-bit software selectable IEPE and AC/DC
analog input C Series module
- NI 9237 4-channel, IEPE strain module
- NI 9239 C Series 4-channel, ±10 V, 24-bit, simultaneous analog input
module
- NI 9263 4-channel analog output module
- NI 9264 C Series 16-channel, ±10 V, 16-bit analog voltage output
module
- NI 9265 C Series 4-channel, 0-20 mA, 16-bit analog current output
module
- NI 9401 8-channel, bidirectional, nibble-configurable digital I/O
module
- NI 9403 C Series 32-channel, TTL digital input/output module
- NI 9411 C Series 6-channel, differential or TTL digital input module
- NI 9421 8-channel, 24 V digital input module
- NI 9421 (DSUB)
- NI 9422 C Series 8-channel, 24 V, sinking/sourcing digital input module
- NI 9423 C Series 8-channel, 24 V, high-speed digital input module
- NI 9425 C Series 32-channel, 24 V, sinking digital input module
- NI 9435 C Series 4-channel, AC/DC universal digital input module
- NI 9472 8-channel, 24 V digital output module
- NI 9472 (DSUB)
- NI 9474 C Series 8-channel, 24 V, high-speed, sourcing digital output
module
- NI 9476 C Series 32-channel, 24 V, high-speed, sourcing digital output
module
- NI 9477 C Series 32-channel, 5-60 V, sinking digital output module
- NI 9481 4-channel Form A SPST Relay digital output module
- NI 9485 8-channel solid-state relay, 60 VDC/30 Vrms, 750 mA C Series
module
- NI BNC-2096 TEDS device
- NI cDAQ-9172 CompactDAQ chassis
- NI DAQPad-6015 for USB (does not have NI-DAQmx simulated device
capability)
- NI DAQPad-6015 for USB (BNC) (does not have NI-DAQmx simulated device
capability)
- NI DAQPad-6015 for USB (Mass Termination) (does not have NI-DAQmx simulated
device capability)
- NI DAQPad-6016 for USB (does not have NI-DAQmx simulated device
capability)
- NI PCI-4461 204.8 kS/s, 24-bit, 2 analog input channel, 2 analog output
channel dynamic signal acquisition TEDS device
- NI PCI-4462 24-bit, 4 analog input channel dynamic signal acquisition TEDS
device
- NI PCI-6010 16 analog input channel device (does not have NI-DAQmx simulated
device capability)
- NI PCI-6122 500 kS/s, 16-bit S Series device
- NI PCI-6123 500 kS/s, 16-bit, 8-channel S Series device
- NI PCI-6132 4-channel, 32 MB S Series device
- NI PCI-6133 3 MS/s, 14-bit, 8 analog input channel S Series device
- NI PCI-6143 250 kS/s, 16-bit, 8 analog input channel S Series device
- NI PCI-6154 4 analog input channel, 4 analog output channel, 16-bit isolated
S Series device
- NI PCI-6220 16 analog input channel, 250 kS/s, 16-bit M Series device
- NI PCI-6221 (68-pin) 16 analog input channel, 250 kS/s, 16-bit M Series
device
- NI PCI-6221 (37-pin) 16 analog input channel, 250 kS/s, 16-bit M Series
device
- NI PCI-6224 32 analog input channel, 250 kS/s, 16-bit M Series device
- NI PCI-6225 80 analog input channel M Series device
- NI PCI-6229 32 analog input channel, 250 kS/s, 16-bit M Series device
- NI PCI-6230 bank isolated, 8 analog input channel, 250 kS/s, 16-bit M Series
device
- NI PCI-6232 250 kS/s, 16-bit, 16 single-ended or 8 differential analog input
channel isolated M Series device
- NI PCI-6233 250 kS/s, 16-bit, 16 single-ended or 8 differential analog input
channel isolated M Series device
- NI PCI-6236 250 kS/s, 4 differential analog input (current input) channel M
Series device
- NI PCI-6238 250 kS/s, 8 differential analog input (current input) channel
isolated M Series device
- NI PCI-6239 250 kS/s, 8 differential analog input (current input) channel
isolated M Series device
- NI PCI-6250 16 analog input channel, 1 MS/s, 16-bit M Series device
- NI PCI-6251 16 analog input channel, 1 MS/s, 16-bit M Series device
- NI PCI-6254 32 analog input channel, 1 MS/s, 16-bit M Series device
- NI PCI-6255 80 analog input channel M Series device
- NI PCI-6259 32 analog input channel, 1 MS/s, 16-bit M Series device
- NI PCI-6280 16 analog input channel, 500 kS/s, 18-bit M Series device
- NI PCI-6281 16 analog input channel, 500 kS/s, 18-bit M Series device
- NI PCI-6284 32 analog input channel, 500 kS/s, 18-bit M Series device
- NI PCI-6289 32 analog input channel, 500 kS/s, 18-bit M Series device
- NI PCI-6509 industrial 96-channel 5V/TTL/CMOS digital I/O device with high
current (24 mA)
- NI PCI-6510 digital I/O device
- NI PCI-6511 digital I/O device
- NI PCI-6512 digital I/O device
- NI PCI-6513 digital I/O device
- NI PCI-6514 digital I/O device
- NI PCI-6515 industrial 32 source/sink digital input, 32 sink digital output
bank isolated digital I/O device
- NI PCI-6516 digital I/O device
- NI PCI-6517 digital I/O device
- NI PCI-6518 digital I/O device
- NI PCI-6519 digital I/O device
- NI PCI-6520 relay board
- NI PCI-6521 relay board
- NI PCI-6528 industrial 24 digital input, 24 digital output CH/CH isolated
digital I/O device
- NI PCI-6624 industrial 8-channel CH/CH isolated counter/timer device
- NI PCI-6722 13-bit, 8 channel analog output device
- NI PCI-6723 13-bit, 32 channel analog output device
- NI PCIe-6251 PCI Express device
- NI PCIe-6259 PCI Express device
- NI PCIe-6536 25 MHz, 5.0/3.3/2.5 V high-speed digital I/O device
- NI PCIe-6537 50 MHz, 5.0/3.3/2.5 V high-speed digital I/O device
- NI PXI-2501 FET multiplexer
- NI PXI-2503 relay multiplexer
- NI PXI-2527
- NI PXI-2529 128-crosspoint relay matrix
- NI PXI-2530 128-channel reed relay multiplexer/matrix
- NI PXI-2532 512-crosspoint matrix
- NI PXI-2545 2.7 GHz 4x1 terminated 50 ohm multiplexer
- NI PXI-2546 2.7 GHz dual 4x1 50 ohm multiplexer
- NI PXI-2547 2.7 GHz 8x1 50 ohm multiplexer
- NI PXI-2548 2.7 GHz 4-SPDT 50 ohm relay module
- NI PXI-2549 2.7 GHz terminated 2-SPDT 50 ohm relay module
- NI PXI-2554 2.5 GHz 4x1 75 ohm multiplexer
- NI PXI-2555 2.5 GHz 4x1 terminated 75 ohm multiplexer
- NI PXI-2556 2.5 GHz dual 4x1 75 ohm multiplexer
- NI PXI-2557 2.5 GHz 8x1 75 ohm multiplexer
- NI PXI-2558 2.5 GHz 4-SPDT 75 ohm relay module
- NI PXI-2559 2.5 GHz terminated 2-SPDT 75 ohm relay module
- NI PXI-2564 16-SPST relay module
- NI PXI-2565 16-SPST relay module
- NI PXI-2566 16-SPDT relay module
- NI PXI-2567 64-channel relay driver
- NI PXI-2568 31-channel SPST relay module
- NI PXI-2569 100-channel SPST relay module
- NI PXI-2570 40-SPDT relay module
- NI PXI-2575 196x1 relay multiplexer
- NI PXI-2576 multi-bank multiplexer
- NI PXI-2584 high-voltage multiplexer
- NI PXI-2585 10-channel multiplexer
- NI PXI-2586 10-channel SPST relay module
- NI PXI-2590 1x4 1.3 GHz multiplexer
- NI PXI-2591 1x4 4 GHz multiplexer
- NI PXI-2593 500 MHz dual 8x1 50 ohm multiplexer
- NI PXI-2594 1x4 2.5 GHz multiplexer
- NI PXI-2595 1x4 5.5 GHz multiplexer
- NI PXI-2596 dual 1x6 26.5 GHz multiplexer
- NI PXI-2597 1x6 26.5 GHz terminated multiplexer
- NI PXI-2598 dual 26.5 GHz transfer switch
- NI PXI-2599 dual 26.5 GHz SPDT
- NI PXI-4200 integrated signal conditioning module
- NI PXI-4204 8-channel 100 V analog input module
- NI PXI-4220 2-channel high-speed strain module
- NI PXI-4224 signal conditioning module
- NI PXI-4461 204.8 kS/s, 24-bit, 2 analog input channel, 2 analog output
channel dynamic signal acquisition device
- NI PXI-4462 24-bit, 4 analog input channel dynamic signal acquisition TEDS
device
- NI PXI-6122 500 kS/s, 16-bit S Series device
- NI PXI-6123 500 kS/s, 16-bit, 8-channel S Series device
- NI PXI-6132 4-channel, 32 MB S Series device
- NI PXI-6133 3 MS/s, 14-bit, 8 analog input channel S Series device
- NI PXI-6143 250 kS/s, 16-bit, 8 analog input channel S Series device
- NI PXI-6220 16 analog input channel, 250 kS/s, 16-bit M Series device
- NI PXI-6221 (68-pin) 16 analog input channel, 250 kS/s, 16-bit M Series
device
- NI PXI-6224 32 analog input channel, 250 kS/s, 16-bit M Series device
- NI PXI-6225 80 analog input channel M Series device
- NI PXI-6229 32 analog input channel, 250 kS/s, 16-bit M Series device
- NI PXI-6230 bank isolated, 8 analog input channel, 250 kS/s, 16-bit M Series
device
- NI PXI-6232 250 kS/s, 16-bit, 16 single-ended or 8 differential analog input
channel isolated M Series device
- NI PXI-6233 250 kS/s, 16-bit, 16 single-ended or 8 differential analog input
channel isolated M Series device
- NI PXI-6236 250 kS/s, 4 differential analog input (current input) channel M
Series device
- NI PXI-6238 250 kS/s, 8 differential analog input (current input) channel
isolated M Series device
- NI PXI-6239 250 kS/s, 8 differential analog input (current input) channel
isolated M Series device
- NI PXI-6250 16 analog input channel, 1 MS/s, 16-bit M Series device
- NI PXI-6251 16 analog input channel, 1 MS/s, 16-bit M Series device
- NI PXI-6254 32 analog input channel, 1 MS/s, 16-bit M Series device
- NI PXI-6255 80 analog input channel M Series device
- NI PXI-6259 32 analog input channel, 1 MS/s, 16-bit M Series device
- NI PXI-6280 16 analog input channel, 500 kS/s, 18-bit M Series device
- NI PXI-6281 16 analog input channel, 500 kS/s, 18-bit M Series device
- NI PXI-6284 32 analog input channel, 500 kS/s, 18-bit M Series device
- NI PXI-6289 32 analog input channel, 500 kS/s, 18-bit M Series device
- NI PXI-6509 industrial 96-channel 5V/TTL/CMOS digital I/O device with high
current (24 mA)
- NI PXI-6511 digital I/O device
- NI PXI-6512 digital I/O device
- NI PXI-6513 digital I/O device
- NI PXI-6514 industrial 32 source/sink digital input, 32 source digital
output bank isolated digital I/O device
- NI PXI-6515 industrial 32 source/sink digital input, 32 sink digital output
bank isolated digital I/O device
- NI PXI-6520 relay board
- NI PXI-6521 relay board
- NI PXI-6528 industrial 24 digital input, 24 digital output CH/CH isolated
digital I/O device
- NI PXI-6624 counter/timer device
- NI PXI-6722 13-bit, 8 channel analog output device
- NI PXI-6723 13-bit, 32 channel analog output device
- NI SC-2350 TEDS device
- NI SCXI-1130 256-channel reed relay multiplexer/matrix
- NI SCXI-1166 32-SPDT relay module
- NI SCXI-1167 64-channel relay driver
- NI SCXI-1169 100-channel SPST relay module
- NI SCXI-1175 196x1 relay multiplexer
- NI SCXI-1190 1.3 GHz quad 4x1 50 ohm multiplexer
- NI SCXI-1191 4 GHz quad 4x1 50 ohm multiplexer
- NI SCXI-1192 18 GHz 8-SPDT 50 ohm relay module
- NI SCXI-1193 quad 8x1 50 ohm multiplexer
- NI SCXI-1194 quad 1x4 2.5 GHz multiplexer
- NI SCXI-1195 quad 1x4 5.5 GHz multiplexer
- NI SCXI-1314T TEDS device
- NI SCXI-1502 thermocouple amplifier module
- NI SCXI-1503 16-channel RTD input module
- NI SCXI-1521/B signal conditioning module
- NI SCXI-1600 USB module (does not have NI-DAQmx simulated device
capability)
- NI USB-6008 (does not have NI-DAQmx simulated device capability)
- NI USB-6009 (does not have NI-DAQmx simulated device capability)
- NI USB-6210 250 kS/s (aggregate)s, 16-bit, 16 single-ended or 8 differential
analog input channel M Series device
- NI USB-6211 250 kS/s (aggregate)s, 16-bit, 16 single-ended or 8
differential analog input channel, 2 analog output channel M Series device
- NI USB-6215 250 kS/s (aggregate)s, 16-bit, 16 single-ended or 8 differential
analog input channel, 2 analog output channel Isolated M Series device
- NI USB-6218 250 kS/s (aggregate)s, 16-bit, 32 single-ended or 16
differential analog input channel, 4 analog output channel Isolated M Series
device
- NI USB-6221 16 analog input channel, 250 kS/s, 16-bit M Series device
- NI USB-6229 32 analog input channel, 250 kS/s, 16-bit M Series device
- NI USB-6251 16 analog input channel, 1 MS/s, 16-bit M Series device
- NI USB-6259 32 analog input channel, 1 MS/s, 16-bit M Series device
- NI USB-6259 (Mass Termination)
- NI USB-6501 (does not have NI-DAQmx simulated device capability)
- NI USB-6525 (does not have NI-DAQmx simulated device capability)
- NI USB-9201 500 kS/s, 12-bit, 8-channel scanned analog input device
- NI USB-9211A 12 S/s, 24-bit, thermocouple analog input, 4-channel scanned
analog input device
- NI USB-9215A 100 kS/s, 16-bit, 4-channel isolated SMIO analog input
device
- NI USB-9221 8-channel scanned analog input device
- NI USB-9233 50 kS/s, 24-bit, 4-channel dynamic signal acquisition
device
- NI USB-9421 8-channel digital input module
- NI USB-9472 8-channel digital output module
- NI USB-9481 4-channel Form A SPST Relay digital output module
Devices Supported in NI-DAQmx and Traditional
NI-DAQ (Legacy)
The following devices are supported in NI-DAQmx and Traditional
NI-DAQ (Legacy). For information on calibrating SCXI devices in NI-DAQmx 8.0
or later, refer to ni.com/info and enter
the info code rdsct4.
- NI DAQCard-6024E 200 kS/s, 12-bit, 16 analog input channel, two analog
output channel, 8 digital I/O line, two counter/timer device
- NI DAQCard-6036E 200 kS/s, 16-bit, 16 analog input channel, two analog
output channel, 8 digital I/O line, two counter/timer device
- NI DAQCard-6062E 500 kS/s, 12-bit, 16 analog input channel device
- NI DAQCard-6715 for PCMCIA 1 MS/s 12-bit analog output device
- NI DAQCard-DIO-24 for PCMCIA 24-channel 5V/TTL/CMOS digital I/O device
- NI PCI-4021 switch controller
- NI PCI-4472 102.4 kS/s, 24-bit, 8 analog input channel dynamic signal
acquisition device
- NI PCI-4474 102.4 kS/s, 24-bit, 4 analog input channel dynamic signal
acquisition device
- NI PCI-6013 200 kS/s, 16-bit, 16 analog input, 8 digital I/O line, two
counter/timer device (does not have NI-DAQmx simulated device capability)
- NI PCI-6014 200 kS/s, 16-bit, 16 analog input channel, two analog output
channel, 8 digital I/O line, two counter/timer analog input device (does not
have NI-DAQmx simulated device capability)
- NI PCI-6023E 200 kS/s, 12-bit, 16 analog input channel, 8 digital I/O line,
two counter/timer device
- NI PCI-6024E 200 kS/s, 12-bit, 16 analog input channel, two analog output
channel, 8 digital I/O line, two counter/timer device
- NI PCI-6025E 200 kS/s, 12-bit, 16 analog input channel, two analog output
channel, 32 digital I/O line, two counter/timer device
- NI PCI-6031E 100 kS/s, 16-bit, 64 analog input channel, two analog output
channel, 8 digital I/O line, two counter/timer device
- NI PCI-6032E 100 kS/s, 16-bit, 16 analog input channel, two analog output
channel, 8 digital I/O line, two counter/timer device
- NI PCI-6033E 100 kS/s, 16-bit, 64 analog input channel, 8 digital I/O line,
two counter/timer device
- NI PCI-6034E 200 kS/s, 16-bit, 16 analog input channel, 8 digital I/O line,
two counter/timer device
- NI PCI-6035E 200 kS/s, 16-bit, 16 analog input channel, two analog output
channel, 8 digital I/O line, two counter/timer device
- NI PCI-6036E 200 kS/s, 16-bit, 16 analog input channel, two analog output
channel, 8 digital I/O line, two counter/timer device
- NI PCI-6052E 333 kS/s, 16-bit, 16 analog input channel, two analog output
channel, 8 digital I/O line, two counter/timer device
- NI PCI-6071E 1.25 MS/s, 12-bit, 64 analog input channel, two analog output
channel, 8 digital I/O line, two counter/timer device
- NI PCI-6110 5 MS/s, 12-bit, 4 channel device
- NI PCI-6111 5 MS/s, 12-bit, 2 channel device
- NI PCI-6115 10 MS/s 12-bit device
- NI PCI-6120 800 kS/s, 16-bit, 4 analog input simultaneous-sampling
device
- NI PCI-6503 24-channel 5V/TTL/CMOS digital I/O device
- NI PCI-6527 24 digital input, 24 digital output CH/CH isolated digital I/O
device
- NI PCI-6533 (DIO-32HS) 32-channel 5 V TTL/CMOS high-speed digital I/O and
handshaking device
- NI PCI-6534 32-channel 5 V TTL/CMOS high-speed digital I/O and handshaking
device with onboard memory
- NI PCI-6601 counter/timer device
- NI PCI-6602 counter/timer device
- NI PCI-6703 16-bit analog output device
- NI PCI-6704 16-bit analog output device
- NI PCI-6711 1 MS/s, 12-bit, 4 channel analog output device
- NI PCI-6713 1 MS/s, 12-bit, 8 channel analog output device
- NI PCI-6731 1 MS/s, 16-bit, 4 channel analog output device
- NI PCI-6733 1 MS/s, 16-bit, 8 channel analog output device
- NI PCI-DIO-96 96-channel parallel digital I/O device
- NI PCI-MIO-16E-1 (PCI-6070) 12-bit, 1.25 MS/s, 16 analog input channel, two
analog output channel, 8 digital I/O line, two counter/timer device
- NI PCI-MIO-16E-4 (PCI-6040E) 500 kS/s (1-channel), 250 kS/s (multichannel),
12-bit, 16 analog input channel, two analog output channel, 8 digital I/O line,
two counter/timer device
- NI PCI-MIO-16XE-10 (PCI-6030E) 100 kS/s, 16-bit, 16 analog input channel,
two analog output channel, 8 digital I/O line, two counter/timer device
- NI PCI-MIO-16XE-50 20 kS/s, 16-bit, 16 analog input channel, two analog
output channel, 8 digital I/O line, two counter/timer device
- NI PXI-1010 8-slot PXI backplane with a 4-slot SCXI backplane chassis
- NI PXI-1011 4-slot PXI backplane with a 8-slot SCXI backplane chassis
- NI PXI-4021 switch controller
- NI PXI-4472 102.4 kS/s, 24-bit, 8 analog input channel dynamic signal
acquisition device
- NI PXI-4472B 102.4 kS/s, 24-bit, 8 analog input channel dynamic signal
acquisition device
- NI PXI-6025E 200 kS/s, 12-bit, 16 analog input channel, two analog output
channel, 32 digital I/O line, two counter/timer device
- NI PXI-6030E 100 kS/s, 16-bit, 16 analog input channel, two analog output
channel, 8 digital I/O line, two counter/timer device
- NI PXI-6031E 100 kS/s, 16-bit, 64 analog input channel, two analog output
channel, 8 digital I/O line, two counter/timer device
- NI PXI-6040E 500 kS/s (1-channel), 250 kS/s (multichannel), 12-bit, 16
analog input channel, two analog output channel, 8 digital I/O line, two
counter/timer device
- NI PXI-6052E 333 kS/s, 16-bit, 16 analog input channel, two analog output
channel, 8 digital I/O line, two counter/timer device
- NI PXI-6070E 1.25 MS/s, 12-bit, 16 analog input channel, two analog output
channel, 8 digital I/O line, two counter/timer device
- NI PXI-6071E 1.25 MS/s, 12-bit, 64 analog input channel, two analog output
channel, 8 digital I/O line, two counter/timer device
- NI PXI-6115 10 MS/s, 12-bit device
- NI PXI-6120 800 kS/s, 16-bit, 4 analog input simultaneous-sampling
device
- NI PXI-6508 96-channel 5V/TTL/CMOS digital I/O device
- NI PXI-6527 24 digital input, 24 digital output CH/CH isolated digital I/O
device
- NI PXI-6533 32-channel 5 V TTL/CMOS high-speed digital I/O and handshaking
device
- NI PXI-6534 32-channel 5 V TTL/CMOS high-speed digital I/O and handshaking
device with onboard memory
- NI PXI-6602 counter/timer device
- NI PXI-6608 counter/timer device
- NI PXI-6704 16-bit analog output device
- NI PXI-6711 1 MS/s, 12-bit, 4 channel analog output device
- NI PXI-6713 1 MS/s, 12-bit, 8 channel analog output device
- NI PXI-6733 1 MS/s, 16-bit, 8 channel analog output device
- NI SCXI-1000 4-slot chassis
- NI SCXI-1000DC 4-slot DC-powered chassis
- NI SCXI-1001 12-slot chassis
- NI SCXI-1100 32-channel analog input module
- NI SCXI-1102 thermocouple amplifier module
- NI SCXI-1102B/C amplifier multiplexer module
- NI SCXI-1104/C multiplexer module
- NI SCXI-1112 thermocouple amplifier module
- NI SCXI-1120/D isolation amplifier module
- NI SCXI-1121 isolation amplifier with excitation module
- NI SCXI-1122 isolated multiplexer amplifier module
- NI SCXI-1124 analog output module
- NI SCXI-1125 isolation amplifier module
- NI SCXI-1126 isolated frequency input channel module
- NI SCXI-1127 32-channel relay multiplexer/matrix
- NI SCXI-1128 32-channel SSR multiplexer/matrix
- NI SCXI-1129 256-crosspoint relay matrix
- NI SCXI-1140 track-and-hold module
- NI SCXI-1141, SCXI-1142, and SCXI-1143 lowpass filter modules
- NI SCXI-1160 16-SPDT general-purpose relay module
- NI SCXI-1161 8-SPDT power relay module
- NI SCXI-1162 digital I/O module
- NI SCXI-1162HV digital I/O module
- NI SCXI-1163 digital I/O module
- NI SCXI-1163R 32-channel solid state relay
- NI SCXI-1520 strain gage input module
- NI SCXI-1530 and SCXI-1531 modules for accelerometers and microphones
- NI SCXI-1540 linear variable differential transformers (LVDT) module
- NI SCXI-1581 current excitation analog output module
Devices Restricted to Traditional NI-DAQ
(Legacy)
NI-DAQmx does not support the following devices. The following
devices are supported only in Traditional NI-DAQ (Legacy):
- NI AT-6022E 12-bit, 100 kS/s, 16-channel analog input, 2-channel analog
output, 8 or 32-digital I/O line, two counter/timer device
- NI AT-AI-16XE-10 100 kS/s, 16-bit, 16 or 64-channel, analog input E Series
device
- NI AT-AO-6 6-channel, 8-digital I/O line, 12-bit, analog output device
- NI AT-AO-10 10-channel, 8-digital I/O line, 12-bit, analog output
device
- NI AT-DIO-32F 32-channel 5 V TTL/CMOS high-speed digital I/O and handshaking
device
- NI AT-MIO-16DE-10 100 kS/s, 12-bit, 16-channel, analog input E Series
device
- NI AT-MIO-16E-1 1.25 MS/s, 12-bit, 16 or 64-channel, analog input E Series
device
- NI AT-MIO-16E-2 500 kS/s, 12-bit, 16 to 64-channel, analog input E Series
device
- NI AT-MIO-16E-10 100 kS/s, 12-bit, 16-channel, analog input E Series
device
- NI AT-MIO-16XE-10 100 kS/s, 16-bit, 16-channel, analog input E Series
device
- NI AT-MIO-16XE-50 20 kS/s, 16-bit, 16-channel, analog input E Series
device
- NI AT-MIO-64E-3 500 kS/s, 12-bit, 16 or 64-channel, analog input E Series
device
- NI DAQCard-AI-16E-4 for PCMCIA
- NI DAQCard-AI-16XE-50 for PCMCIA
- NI DAQCard-6533 digital I/O for PCMCIA
- NI DAQPad-6020E 100 kS/s, 12 bit E Series device
- NI DAQPad-6052E 333 kS/s, 16-bit E Series device
- NI DAQPad-6070E 1.25 MS/s, 12-bit E Series device
- NI DAQPad-6507 for USB 96-channel 5V/TTL/CMOS digital I/O device with
built-in screw terminals
- NI DAQPad-6508 for USB 96-channel 5V/TTL/CMOS digital I/O device with
100-pin I/O connector
- NI PC-DIO-24 24-channel 5V/TTL/CMOS digital I/O device
- NI PC-DIO-96 96-bit parallel digital I/O device
- NI PCI-4451/4452/4454 dynamic signal acquisition and generation device
- NI PCI-4551/4552 dynamic signal acquisition device
- NI PCI-7030 RT Series device
- NI PCI-7041/6040E device for LabVIEW RT (only supported in LabVIEW 8.0
or earlier and NI-DAQmx 8.1 or earlier)
- NI PXI-4551/4552 dynamic signal acquisition device
- NI PXI-7030 RT Series device
Devices No Longer Supported in NI-DAQmx 8.3 and
Later
The following products are not supported in NI-DAQmx
8.3 and later and will not be supported in future versions of NI-DAQmx:
- NI PCI-7041/6040E device for LabVIEW RT is supported in NI-DAQmx 8.1 and
earlier.
Devices No Longer Supported in NI-DAQ 7.x
and Later
The following products are not supported in NI-DAQmx
7.x and later or Traditional NI-DAQ (Legacy) 7.x and will not
be supported in future versions of NI-DAQ. All references to unsupported
products, such as VXI-DAQ devices, should be ignored. You must use NI-DAQ
version 6.9.x or earlier to program these devices:
- NI AT-MIO-16F-5 multifunction DAQ device
- NI DAQCard-500 PCMCIA MIO device
- NI DAQCard-516 PCMCIA MIO device
- NI DAQCard-700 PCMCIA MIO device
- NI DAQCard-1200 PCMCIA MIO device
- NI DAQCard-AO-2DC PCMCIA low-cost analog output and current loop DAQ
device
- NI DAQPad-1200 DAQ device and control for parallel port
- NI DAQPad-MIO-16XE-50 16-bit DAQ device and control for parallel port
- NI Lab-PC
- NI Lab-PC+ PC/XT MIO device
- NI Lab-PC-1200 ISA MIO device
- NI Lab-PC-1200/AI PC/XT MIO device
- NI PC-516 16-bit, 50 kS/s MIO device
- NI PC-AO-2DC low-cost analog output and current loop DAQ device
- NI PC-LPM-16/PNP MIO device for the PC
- NI PC-OPDIO-16 optically isolated digital I/O device for the PC
- NI PC-TIO-10 timing and digital I/O interface for the PC
- NI PCI-1200 12-bit, 100 kS/s MIO device
- NI SCXI-1200 12-bit DAQ and control module
- NI SCXI-2000 4-slot chassis
- NI SCXI-2400 serial interface module
- NI VXI-AO-48XDC DC setpoint module for VXI bus
- NI VXI-DIO-128 digital I/O module for VXI bus
- NI VXI-MIO-64E-1 12-bit MIO module for VXIbus
- NI VXI-MIO-64XE-10 16-bit MIO module for VXIbus
- NI VXI-SC-1000 carrier
- NI VXI-SC-1100 carrier
- NI VXI-SC-1102/B/C 32-channel multiplexer amplifier submodule
- NI VXI-SC-1150 carrier for SMBs
- NI VXI-TB-1000 terminal block
- NI VXI-TB-1303 terminal block
System Requirements
Development
| Minimum
Processor |
Pentium III/Celeron 600 MHz or
Equivalent |
| RAM |
128 MB |
| Screen resolution |
800 x 600 pixels |
| Operating system |
Windows 2000/XP or later |
| Recommended Processor |
Pentium 4 or Equivalent |
| RAM |
256 MB |
| Screen resolution |
1024 x 768 pixels |
| Operating system |
Windows 2000/XP or later |
Deployment
| Minimum Processor |
Pentium 200 MHz or Equivalent |
| RAM |
64 MB |
| Screen resolution |
800 x 600 pixels or no screen |
| Operating system |
Windows 2000/XP or later |
| Recommended Processor |
Pentium III/Celeron 600 MHz or
Equivalent |
| RAM |
256 MB |
| Screen resolution |
1024 x 768 pixels or no screen |
| Operating system |
Windows 2000/XP or later |
You must have Internet Explorer version 5.0 or later to use some
features of the NI-DAQ 7.x and later documentation, including the help
system and Device Document Browser.
If you are using either an M Series USB device or NI cDAQ-9172
CompactDAQ chassis, you must run either Windows Vista, Windows XP Service Pack 2
or greater, or Windows 2000 Service Pack 4 or greater.